Category: DIN

DIN TEST STANDARDS

DIN 3-8 / DIN EN 3-8 : Portable fire extinguishers – Part 8: Requirements for the construction, pressure resistance and mechanical tests for extinguishers with a maximum allowable pressure equal to or lower than 30 bar, which comply with the requirements of EN 3-7

DIN 34 / – DIN ISO 34-1 : Rubber, vulcanized or thermoplastic — Determination of tear strength — Part 1: Trouser, angle and crescent test pieces

DIN 178 / DIN EN ISO 178 : Plastics — Determination of flexural properties

DIN 267 : Fasteners – Technical specification. Tensile strength testing.

DIN 302-3 / DIN EN 302-3 : Adhesives for load-bearing timber structures – Test methods – Part 3: Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength

DIN 306 / DIN EN ISO 306 : Plastics – Thermoplastic materials – Determination of Vicat softening temperature (VST)

DIN 310 / DIN EN 310 : Wood-based panels; determination of modulus of elasticity in bending and of bending strength

DIN 311 / DIN EN 311 : Wood-based panels – Surface soundness – Test method

DIN 314-1 / DIN EN 314-1 : Plywood – bonding quality: part 1: test methods

DIN 319 / DIN EN 319 : Particleboards and fibreboards; determination of tensile strength perpendicular to the plane of the board

DIN 320 / DIN EN 320 : Particleboards and fibreboards – Determination of resistance to axial withdrawal of screws

DIN 388 / DIN EN 388 : Protective gloves against mechanical risks

DIN 392 / DIN EN 392 : Glued laminated timber – Shear test glue lines

DIN 408 / DIN EN 408 : Timber structures – Structural timber and glued laminated timber – Determination of some physical and mechanical properties

DIN 433 / DIN EN 433 : Resilient floor coverings – Determination of residual indentation after static loading

DIN 455 / DIN EN 455 : Medical Gloves for Single-Use

DIN 488 / DIN EN 488 : District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks.

DIN 488-2 : Reinforcing steels – Reinforcing steel bars

DIN 488-5 : Reinforcing steels – Lattice girders. Shear test. Part 2.

DIN 520 / DIN EN 520 : Gypsum plasterboards – Definitions, requirements and test methods.

DIN 527-2 / DIN EN ISO 527-2 : Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics

DIN 527-3 / DIN EN ISO 527-3 : Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets

DIN 582 / DIN EN 582 : Thermal spraying; determination of tensile adhesive strength

DIN 604 / DIN EN ISO 604 : Plastics – Determination of compressive properties

DIN 763 : Tested, non-calibrated, long-link round steel chains

DIN 789 / DIN EN 789 : Timber structures – Test methods – Determination of mechanical properties of wood based panels

DIN 813 / DIN ISO 813 : Determination of adhesion to a rigid substrate – 90 degree peel method

DIN 826 / DIN EN 826 : Thermal insulating products for building applications – Determination of compression behaviour

DIN 844 / DIN EN ISO 844 : Rigid cellular plastics — Determination of compression properties

DIN 843-1-1 / DIN EN 843-1- 1 : Advanced technical ceramics – Mechanical properties of monolithic ceramics at room temperature – Part 1: Determination of flexural strength

DIN 863 / DIN EN 863 : Protective clothing – Mechanical properties – Test method: Puncture resistance

DIN 868-5 / DIN EN 868-5 : Packaging for terminally sterilized medical devices – Part 5: Sealable pouches and reels of porous materials and plastic film construction

DIN 898-1 / DIN EN ISO 898-1 : Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread

DIN 898-2 / DIN EN ISO 898-2 : Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread

DIN 1170-4 / DIN EN 1170-4 : Precast concrete products – Test method for glass-fibre reinforced cement – Part 4: Measuring bending strength; “simplified bending test” method

DIN 1193 : Steel hammers – Technical specifications

DIN 1279-4 / DIN EN 1279-4 : Glass in building – Insulating glass units – Part 4: Methods of test for the physical attributes of edge seal components and inserts

DIN 1288-3 / DIN EN 1288-3 : Glass in building – Determination of the bending strength of glass – Part 3: Test with specimen supported at two points (four point bending)

DIN 1293 : General requirements for components used in pneumatically pressurized

DIN EN 1293 : Discharge pipes, drains and sewers

DIN 1324 / DIN EN 1324 : Adhesives for tiles – Determination of shear adhesion strength of dispersion adhesives

DIN 1348 / DIN EN 1348 : Adhesives for tiles – Determination of tensile adhesion strength for cementitious adhesives

DIN 1372 / DIN EN 1372 : Test method for adhesives for floor and wall coverings – Peel test

DIN 1464 / DIN EN 1464 : Adhesives – Determination of peel resistance of adhesive bonds – Floating roller method

DIN 1465 / DIN EN 1465 : Adhesives – Determination of tensile lap-shear strength of bonded assemblies

DIN 1607 / DIN EN 1607 : Thermal insulating products for building applications – Determination of tensile strength perpendicular to faces

DIN 1608 / DIN EN 1608 : Thermal insulating products for building applications – Determination of tensile strength parallel to faces

DIN 1719 / DIN EN 1719 : Adhesives for paper and board, packaging and disposable sanitary products – Tack measurement for pressure sensitive adhesives – Determination of loop tack

DIN 1806 / DIN EN ISO 1806 : Fishing nets – Determination of mesh breaking force of netting

DIN 1922 / DIN EN ISO 1922 : Determination of shear properties

DIN 1927-6 / DIN EN ISO 1927-6 : Monolithic (unshaped) refractory products – Part 6: Measurement of physical properties. 6. Determination of cold crushing strength.

DIN 1939 / DIN EN 1939 : Self adhesive tapes – Determination of peel adhesion properties

DIN 2039-1 / DIN EN ISO 2039-1 : Plastics – Determination of hardness – Part 1: Ball indentation method

DIN 2137 / DIN ISO 2137 : Rigid cellular plastics — Determination of tensile properties

DIN 2243-2 / DIN EN 2243-2 : Petroleum products and lubricants – Determination of cone penetration of lubricating greases and petrolatum

DIN 2243-3 : Aerospace series – Non-metallic materials – Structural adhesives – Test method – Part 3: Peeling test metal- honeycomb core

DIN 2243-4 / DIN EN 2243-4 : Aerospace series – Non-metallic materials – Structural adhesives – Test method – Part 4: Metal-honeycomb core flatwise tensile test

DIN 2377 / DIN EN 2377: Aerospace series; glass fibre reinforced plastics; test method; determination of apparent interlaminar shear strength

DIN 2439 / DIN EN ISO 2439 : Flexible cellular polymeric materials — Determination of hardness (indentation technique)

DIN 2562 / DIN EN 2562 : Aerospace series – Carbon fibre reinforced plastics – Unidirectional laminates; flexural test parallel to the fibre direction

DIN 2563 / DIN EN 2563 : Aerospace series – Carbon fibre reinforced plastics – Unidirectional laminates; determination of apparent interlaminar shear strength

DIN 2759 / DIN EN ISO 2759 : Board – Determination of bursting strength

DIN 3037 / DIN EN ISO 3037 : Corrugated fibre board — Determination of edgewise crush resistance (unwaxed edge method)

DIN 3303-1 / DIN EN ISO 3303-1 : Bursting strength of rubber- or plastics- coated fabrics – Part 1: Steel-ball method

DIN 3327 / DIN EN ISO 3327 : Hard metals – Determination of transverse rupture strength

DIN 3377- 2 / DIN EN ISO 3377- 2 : Leather – Physical and mechanical tests – Determination of tear load – Part 2: Double edge tear

DIN 3379 / DIN EN ISO 3379 : Leather – Determination of distension and strength of surface (Ball burst method)

DIN 3386-1 / DIN EN ISO 3386-1 : Polymeric materials, cellular flexible – Determination of stress-strain characteristics in compression – Part 1: Low-density materials

DIN 3651-2 / DIN EN ISO 3651-2 : Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid

DIN 3781 / DIN ISO 3781 : Paper and board — Determination of tensile strength after immersion in water

DIN 4108-11 : Thermal insulation and energy economy in buildings – Part 11: Minimum requirements to the durability of bond strength with adhesive tapes and adhesive masses for the establishment of airtight layers

DIN 4226-1 : Aggregates for concrete and mortar – Part 1: Normal and heavy-weight aggregates

DIN 4226-2 : Aggregates for concrete; aggregates of porous structure (lightweight aggregates); terminology, designation and requirements

DIN 4624 / DIN EN ISO 4624 : Paints and varnishes, pull off test for adhesion

DIN 4843 : Safety footwear; safety requirements, testing

DIN 5173 / DIN EN ISO 5173 : Destructive tests on welds in metallic materials – Bend tests

DIN 5299 : Snap hook

DIN 6259-3 / DIN EN ISO 6259-3 : Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes

DIN 6507-2 / DIN EN ISO 6507-2 : Metallic materials – Vickers hardness test – Part 2: Verification and calibration of testing machines

DIN 6872 / DIN EN ISO 6872 : Dentistry – Ceramic materials

DIN 6892 / DIN EN ISO 6892 : Metallic materials – Tensile testing – Part 1: Method of test at room temperature

DIN 6899 : Steel thimbles for fibre ropes

DIN 7389 / DIN EN ISO 7389 : Building construction – Jointing products – Determination of elastic recovery of sealants

DIN 7438 / DIN EN ISO 7438 : Metallic materials — Bend test

DIN 7808 / DIN EN ISO 7808 : Plastics – Thermosetting moulding materials – Determination of transfer flow

DIN 7864 / DIN EN ISO 7864 : Tensile test fixture to test sterile hypodermic needles

DIN 7886-1 / DIN EN ISO 7886-1 : Sterile hypodermic syringes for single use – Part 1: Syringes for manual use

DIN 8295 / DIN EN ISO 8295 : Plastics – Film and sheeting – Determination of the coefficients of friction

DIN 8339 / DIN EN ISO 8339 : Building construction – Sealants – Determination of tensile properties (Extension to break)

DIN 8340 / DIN EN ISO 8340 : Determination of tensile properties at maintained extension

DIN 8493 / DIN EN ISO 8493 : Metallic materials – Tube – Drift- expanding test

DIN 8895 / DIN EN ISO 8895 : Shaped insulating refractory products – Determination of cold crushing strength

DIN 9046 / DIN EN ISO 9046 : Building construction – Jointing products – Determination of adhesion/cohesion properties of sealants at constant temperature

DIN 9073-5 / DIN EN ISO 9073-5 : Textiles – Test methods for nonwovens – Part 5: Determination of resistance to mechanical penetration (ball burst procedure)

DIN 9073-7 / DIN EN ISO 9073-7 : Textiles – Test methods for nonwovens – Part 7: Determination of bending length

DIN 9073-18 / DIN EN ISO 9073-18 : Textiles — Test methods for nonwovens — Part 18: Determination of breaking strength and elongation of nonwoven materials using the grab tensile test

DIN 9187-1 / DIN EN ISO 9187-1 : Injection equipment for medical use – Part 1: Ampoules for injectables

DIN 9626 / DIN EN ISO 9626 : Stainless steel needle tubing for the manufacture of medical devices – Requirements and test methods

DIN 9665 / DIN EN ISO 9665 : Adhesives – Animal glues – Methods for sampling and testing

DIN 9836-1 / DIN EN ISO 9836-1 : Geosynthetics – Determination of thickness at specified pressures – Part 1: Single layers

DIN 10080 / DIN EN 10080 : Steel for the reinforcement of concrete – Weldable reinforcing steel – General

DIN 10130 / DIN EN 10130 : Cold rolled low carbon steel flat products for cold forming – Technical delivery conditions

DIN 10223-3 / DIN EN 10223- 3 : Steel wire and wire products for fencing and netting – Part 3: Hexagonal steel wire mesh products for civil engineering purposes

DIN 10223-8 / DIN EN 10223-8 : Steel wire and wire products for fencing and netting – Part 8: Welded mesh gabion products

DIN 10319 / DIN EN ISO 10319 : Geosynthetics – Wide-width tensile test

DIN 10354 / DIN EN ISO 10354 : Adhesives – Characterization of durability of structural-adhesive- bonded assemblies – Wedge rupture test

DIN 10477 / DIN EN ISO 10477 : Dentistry – Polymer-based crown and veneering materials

DIN 10545 / DIN EN ISO 10545 : Ceramic tiles – Part 2: Determination of dimensions and surface quality

DIN 11542-2 / DIN EN ISO 11542-2 : Plastics – Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials – Part 2: Preparation of test specimens and determination of properties

DIN 11600 / DIN EN ISO 11600 : Building construction – Jointing products – Classification and requirements for sealants

DIN 11608-3 / DIN EN ISO 11608-3 : Needle-based injection systems for medical use – Requirements and test methods – Part 3: Finished containers

DIN 11644 / DIN EN ISO 11644 : Leather – Test for adhesion of finish

DIN 11979-3 / DIN EN ISO 11979-3 : Ophthalmic implants – Intraocular lenses – Part 3: Mechanical properties and test methods. Compression test.

DIN 12002 / DIN EN 12002 : Adhesives for tiles – Determination of transverse deformation for cementitious adhesives and grouts

DIN 12003 / DIN EN 12003 : Adhesive for tiles – Determination of shear adhesion strength of reaction resin adhesives

DIN 12004 / DIN EN 12004 : Adhesives for tiles – Requirements, evaluation of conformity, classification and designation

DIN 12089 / DIN EN 12089 : Thermal insulating products for building applications – Determination of bending behaviour

DIN 12090 / DIN EN 12090 : Shear properties of sandwich core materials

DIN 12190 / DIN EN 12190 : Determination of compressive strength of repair mortar

DIN 12192 / DIN EN ISO 12192 : Paper and board — Determination of compressive strength — Ring crush method

DIN 12230 / DIN EN 12230 : Surfaces for sports areas. Determination of tensile properties of synthetic sports surfaces

DIN 12236 / DIN EN ISO 12236 : Static puncture test on geotextiles

DIN 12242 / DIN EN 12242 : Touch and close fasteners – Determination of peel strength

DIN 12259-1 / DIN EN 12259- 1 : Fixed firefighting systems – Components for sprinkler and water spray systems – Part 1: Sprinklers

DIN 12310-1 / DIN EN 12310- 1 : Flexible sheets for waterproofing – Part 1: Bitumen sheets for roof waterproofing; determination of resistance to tearing (nail shank).

DIN 12311-2 / DIN EN 12311- 2 : Flexible sheets for waterproofing – Determination of tensile properties – Part 2: Plastic and rubber sheets for roof waterproofing

DIN 12311-2 / DIN EN 12311- 2 : Flexible sheets for waterproofing – Determination of tensile properties – Part 2: Plastic and rubber sheets for roof waterproofing

DIN 12372 / DIN EN 12372 : Natural stone test methods – Determination of flexural strength under concentrated load

DIN 12402-Fig1 / DIN EN ISO 12402-Fig1 : Standard for personal flotation devices

DIN 12430 / DIN EN 12430 : Thermal insulating products for building applications – Determination of behaviour under point load

DIN 12431 / DIN EN 12431 : Thermal insulating products for building applications. Determination of thickness for floating floor insulating products

DIN 12467 DIN EN 12467 : Fibre-cement flat sheets – Product specification and test methods

DIN 12625-5 / DIN EN ISO 12625-5 : Tissue paper and tissue products – Part 5: Determination of wet tensile strength

DIN 12625-9 / DIN EN ISO 12625-9 : Tissue paper and tissue products – Part 9: Determination of ball burst strength

DIN 12773 / DIN EN 12773 : Footwear – Test methods for outsoles – Needle tear strength

DIN 12814-2 / DIN EN 12814- 2 : Testing of welded joints of thermoplastics semi-finished products – Part 2: Tensile test

DIN 12814-4 / DIN EN 12814- 4 : Testing of welded joints of thermoplastics semi-finished products – Part 4: Peel test

DIN 13055-1 / DIN EN 13055- 1 : Lightweight aggregates – Part 1: Lightweight aggregates for concrete, mortar and grout

DIN 13354 / DIN EN 13354 : Solid wood panels (SWP) – Bonding quality

DIN 13393 / DIN EN 13393 : Packaging – Specification for edge protectors

DIN 13446 / DIN EN 13446 : Wood-based panels – Determination of withdrawal capacity of fasteners

DIN 13503-2 / DIN EN ISO 13503-2 : Petroleum and natural gas industries — Completion fluids and materials – Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations

DIN 13523-1 / DIN EN 13523- 1 : Coil coated metals – Test methods – Part 1: Film thickness

DIN 13555 / DIN EN 13555 : Flanges and their joints – Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections

DIN 13572 / DIN EN 13572 : Footwear – Test methods for uppers, lining and insocks – Seam strength

DIN 13892-2 / DIN EN 13892- 2 : Methods of test for screed materials – Part 2: Determination of flexural and compressive strength

DIN 13934 / DIN EN ISO 13934 : Textiles – Tensile properties of fabrics – Part 1: Determination of maximum force and elongation at maximum force using the strip method

DIN 13936-1 / DIN EN ISO 13936-1 : Textiles – Determination of the slippage resistance of yarns at a seam in woven fabrics – Part 1: Fixed seam opening method

DIN 13936-2 / DIN EN ISO 13936-2 : Textiles – Determination of the slippage resistance of yarns at a seam in woven fabrics – Part 2: Fixed load method

DIN 13936-3 / DIN EN ISO 13936-3 : Textiles – Determination of the slippage resistance of yarns at a seam in woven fabrics – Part 3: Needle clamp method

DIN 14024 / DIN EN 14024 : Metal profiles with thermal barrier. Mechanical performance. Requirements, proof and tests for assessment

EN 14080 / DIN EN 14080 : Timber structures – Glued laminated timber and glued solid timber – Requirements Timber structures – Glued laminated timber and glued solid timber – Requirements

DIN 14125 / DIN EN ISO 14125 : Fibre-reinforced plastic composites – Determination of flexural properties

DIN 14126 / DIN EN ISO 14126 : Fibre-reinforced plastic composites – Determination of compressive properties in the in-plane direction

DIN 14130 / DIN EN ISO 14130 : Fibre reinforced plastic composites – Determination of apparent interlaminar shear strength by short beam-method

DIN 14272 / DIN EN ISO 14272 : Resistance welding – Destructive testing of welds – Specimen dimensions and procedure for cross tension testing of resistance spot and embossed projection welds

DIN 14279 / DIN EN 14279 : Laminated Veneer Lumber (LVL) – Definitions, classification and specifications

DIN 14410 / DIN EN 14410 : Self adhesive tapes – Measurement of breaking strength and elongation at break

DIN 14444 / DIN EN 14444 : Structural adhesives – Qualitative assessment of durability of bonded assemblies – Wedge rupture test

DIN 14704-1 / DIN EN 14704- 1 : Determination of the elasticity of fabrics – Part 1: Strip tests

DIN 14477 DIN EN 14477 : Packaging, Flexible packaging material – Determination of puncture resistance – Test methods

DIN 14509 / DIN EN 14509 : Self-supporting double skin metal faced insulating panels – Factory made products – Specifications

DIN 14555 / DIN EN ISO 14555 : Welding – Arc stud welding of metallic materials

DIN 14801 / DIN EN ISO 14801 : Dentistry – Implants – Dynamic loading test for endosseous dental implants

DIN 14891 / DIN EN 14891 : Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives. Requirements, test methods, assessment and verification of constancy of performance, classification and marking

DIN 14916 / DIN EN ISO 14916 : Thermal spraying – Determination of tensile adhesive strength

DIN 15048-1 / DIN EN 15048- 1 : Non-preloaded structural bolting assemblies – Part 1: General requirements

DIN 15630-2 / DIN EN ISO 15630-2 : Steel for the reinforcement and prestressing of concrete – Test methods – Part 2: Welded fabric and lattice girder

DIN CEN/TR 16792-Fig.B5 : Safety of children’s clothing – Recommendations for the design and manufacture of children’s clothing – Mechanical safety. Button pull-off test

DIN 17271 / DIN EN 17271 : Plastics – Poly(vinyl chloride) (PVC) based profiles – Determination of the peel strength of profiles laminated with foils

DIN 17333-4 / DIN EN 17333- 4 : Characterization of One Component Foam (OCF) – Part 1: Yield Measurement of the tensile strength of polyurethane foam

DIN 17697 / DIN EN ISO 17697 : Footwear – Test methods for uppers, lining and insocks – Seam strength

DIN 18134 : Soil – Testing procedures and testing equipment – Plate load test

DIN 18164-1 : Cellular plastics as insulating building materials; insulating materials thermal insulation

DIN 19304 : Testing of corrugated board-Creasings

DIN 19736 / DIN ISO 19736 : Dentistry – Bonding test between polymer teeth and denture base materials

ISO 20126 / DIN EN ISO 20126 : Dentistry — Manual toothbrushes — General requirements and test methods

DIN 20482 / DIN EN ISO 20482 : Testing of metals; Erichsen cupping test on sheet and strip metal having a width of >= 90 mm; Thickness range: 0.2 mm to 2 mm

DIN 20795-1 / EN ISO 20795-1 : Dentistry – Artificial teeth for dental prostheses

DIN 21182 / DIN EN ISO 21182 : Light conveyor belts – Determination of the coefficient of friction

DIN 22112 / DIN EN ISO 22112 : Dentistry – Artificial teeth for dental prostheses

DIN 22254 / DIN EN ISO 22254 : Dentistry – Manual toothbrushes – Resistance of tufted portion to deflection

DIN 23910 / DIN EN ISO 23910 : Leather – Physical and mechanical tests – Measurement of stitch tear resistance

DIN 23936-2- B.2 / DIN EN ISO 23936-2- B.2 : Petroleum, petrochemical and natural gas industries – Non-metallic materials in contact with media related to oil and gas production – Part 2: Elastomers

DIN 28510-1 / DIN EN 28510- 1 : Adhesives – Peel test for a flexible- bonded-to-rigid test specimen assembly – Part 1: 90° peel

DIN 29022 / DIN EN ISO 29022 : Dentistry – Adhesion – Notched-edge shear bond strength test

DIN 29862 / DIN EN ISO 29862 : Self adhesive tapes – Determination of peel adhesion properties

DIN 40802-1 : Metal-clad base material for printed circuits;specifications

DIN 50101-1: Testing of metals; Erichsen cupping test on sheet and strip metal having a width of >= 90 mm; Thickness range: 0.2 mm to 2 mm

DIN 50101-2 : Testing of metals; Erichsen cupping test on sheet and strip metal having a width of >= 90 mm; Thickness range: over 2 mm up to 3 mm

DIN 50109 : Tensile testing of lamellar graphite cast iron

DIN 50114 : Testing of metals; tensile test on sheet or strip without using an extensometer

DIN 50125 : Testing of metallic materials – Tensile test pieces

DIN 50141 : Testing of metals; Shear test

DIN 50146 / DIN EN 50146 : Cable ties for electrical installations

DIN 50139 : Testing of Steel; Flanging Test on Tubes

DIN 50342-5 / DIN EN 50342- 5 : Lead-acid starter batteries – Part 5: Properties of battery housings and handles

DIN 52186 : Testing of wood- Bending test

DIN 52187 : Testing of wood; determination of ultimate shearing stress parallel to grain

DIN 52292-1 : Testing of glass and glass ceramics; determination of bending strength; coaxial double ring bending test on flat specimens with small test area

DIN 52352 : Testing of wood fibre boards; bend testing

DIN 52365 : Testing of wood chipboards; determination of tensile strength vertical to the chipboard plane

DIN 52367 : Wood-based panels – Determination of shear strength parallel to the surface

DIN 52371 : Testing of plywood; bending test

DIN 52377 : Testing of plywood – Determination of modulus of elasticity in tension and of tensile strength

DIN 52455-3 : Testing of sealants in building construction – Adhesion and extension test – Part 3: Influence of light through glass

DIN 53121 : Testing of paper and board – Determination of the bending stiffness by the beam method

DIN 53142-2 : Testing of board – Puncture test – Part 2: Puncture test with linear move

DIN 53278 : Testing of adhesives for floor coverings; testing of peel-resistance of bondings, reaction adhesives for rubber floor-coverings described in DIN 16852

DIN 53289 :

DIN 53292 : Testing of sandwiches; Tensile test perpendicular to the faces

DIN 53294 : Shear properties of sandwich core materials

DIN 53295 : Peel resistance of adhesive bonds, e.g. for honeycomb sandwich constructions

DIN 53331 : Leather – Measurement of stitch tear resistance

DIN 53357 : Testing of plastics sheets; adhesion test

DIN 53362 : Testing of plastics films and textile fabrics (excluding nonwovens), coated or not coated fabrics – Determination of stiffness in bending – Method according to Cantilever

DIN 53375 : Testing of plastic film and sheeting; determination of the coefficients of friction

DIN 53430 : Testing of Rigid Cellular Materials; Tensile Test

DIN 53494 : Electroplated coatings; testing of electroplated plastic articles; determination of peel strength

DIN 53504 : Testing of rubber – Determination of tensile strength at break, tensile stress at yield, elongation at break and stress values in a tensile test

DIN 53506 : Testing of rubber; determination of needle tear resistance

DIN 53515 : Determination of tear strength of rubber elastomers and plastic film using Graves angle test piece with nick

DIN 53531-1 : Determination of the adhesion of rubber to rigid materials by the one- plate method

DIN 53579-2 : Testing of flexible cellular materials; hardness test on finished parts; compression test on profiles

DIN 53769-1 : Testing of glass fibre reinforced plastics pipes; determination of the longitudinal shear strength of type B pipe fittings

DIN 53857 : Testing of textiles; simple tensile test on strips of textile fabrics, woven fabrics and ribbons

DIN 53858 : Testing of textiles; determination of the breaking strength of textile fabrics (with the exception of nonwoven textiles), grab method

DIN 54307 (superseded by ISO 12236) : Testing of geotextiles and geotextile related products; static puncture test (CBR) (proposal for a European Standard)

DIN 54516 : Testing of paper and board – Determination of plybond resistance

DIN 60793-1- 32 / DIN EN/IEC 60793-1-32 : Optical fibres – Part 1-32: Measurement methods and test procedures – Coating strippability

DIN 61061-1 / DIN EN 61061- 1 : Non-impregnated densified laminated wood for electrical purposes – Part 1: Definitions, designation and general requirements

DIN 61386-1 / DIN EN 61386- 1 : Conduit systems for cable management – Part 1: General requirements

DIN 65561 : Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of compressive strength after impact test

DIN 68501 : Hardware for furniture – Test methods for determination of strength and stiffness of cabinet connectors

No products were found matching your selection.
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
Click outside to hide the comparison bar
Compare